This 2003 Ford Expedition came in with a no run condition. A quick check found no fuel pressure and a code P0231 (low voltage on fuel pump monitor circuit). I decided to go to the interior fuse box, where my wiring diagrams, stated the fuel pump relay and fuse are located. There are a couple of covers that have to be removed.
Pull the edge loose at the firewall end and pivot the cover back.
There is a black plastic cover that has to be pulled off of the actual fuse box.
Since my wiring diagrams stated the relay was located in the fuse box, but did not give a specific position, I looked in the owners manual for more info. No luck there. I did some reading and found that there are five internal, non serviceable relays inside the fuse block. My next test would involve locating the output circuit from the relay. The wiring diagrams stated that the fuel pump relay output wire was dark green/yellow and it was located in cavity 3 of connector C270K. I placed a jumper wire into the cavity to backprobe the circuit, no volts. Since my backprobe wire is part of a fused jumper wire, I connected battery voltage to the circuit and started the vehicle. This told me that the fuel pump, inertia switch and related wiring were all okay.
I checked fuse #34 with the key on and it had power and was good so that eliminated a faulty pcm relay and related wiring. The next step was to locate the light blue/orange wire in cavity #12 of the C270B connector. It is in the lower right hand corner of the twelve cavity connector just below the connector that I am backprobing in the picture above. When the ignition is turned on the reading was near zero volts and after a few seconds it went to battery voltage. This told me that the pcm was using a ground to energize the fuel pump relay coil. With all of this testing I knew without a doubt that the fuel pump relay that is part of the interior fuse box was faulty.
Disconnect the battery first before removing the fuse block. There is a battery feed cable that also has to be disconnected on the rear edge of the fuse box. It is located under a cover. I have pictures of that at the end of this post. There is only one bolt that holds this fuse block in place.
I unplugged all of the wiring. There are connectors on the top where testing was done and on the edge. Above and below the mounting bolt.
In the rear.
This connector has a slide mechanism. I have my finger in the pull handle for it.
The fuse block removed from the vehicle. You can see the battery terminal post on the lower left edge.
I carefully removed all fuses and relays from the fuse block and laid them out in the order removed.
I took the back cover off of the fuse block and started disassembling it.
Once I had it opened it was easy to see the damage. Slightly right of center.
The damage was even easier to see from the relay side of the board. I feel fairly confident that if this problem would have been caught soon enough, the solder joint could have been repaired or a new relay installed (if one could have been located).
The old fuse block on the left and the new one on the right.
I plugged everything back in and bolted the fuse block in place.
This is the end of the battery cable that I referred to earlier.
The cover for the battery stud on the fuse block.
I put all of the covers back on, cleared the codes and test drove the vehicle. This one is done.
This repair will generally apply to Ford and Lincoln full sized trucks and suv’s in the same years//body style. Check diagrams and component locators before jumping any circuits, as I did.
Hi was hoping you could give some in site to what my problem may be. I have bought and changed the fuse box now the only difference between the 2 boxes is that the old box has the number 9 fuse (alternator fuse) and the new box does not have that fuse ford says that we don’t need that fuse for the new box changed the box got it all back together got check charging system error I was then advised to get a new alternator and battery changed both of those still get the same error. What should my next step be should I try to find a box with the number 9 fuse?
It sounds like one or more connectors are disconnected or at least not fully seated.
Please help! I had gotten to this point prior to finding your blog my fuse box was also burnt so I bought a new one put it in and started right up except now it says check charging system, Abs light is on the check reverse sensor, auto lights don’t work driver seat wont adjust heat and air don’t come on I don’t know if I did something wrong or what my next step should be. Thanks
If the connection is just cracked it can be resoldered, if you have the time and inclination. If not replacing the fuse box assembly will eliminate the poor connection . Assuming that your testing has lead to this point. It is also a good idea to check the fuel pump amperage draw to make sure the condition does not return to the new fuse box.
My ford expedition 2003 has this same problem. It also has alot of miles. So my question is when you said , “Sometimes you can re solder the loose connection if it is just starting to fail.” Do you mean that the loose connection that is causing my box to melt in the first place is on the backside of the box and when I get a new fuse box I will solve the problem and should not have to put more money into the wireing? To many miles on it to put alot into it!!! thanks