This 2005 GMC Sierra came in with the complaint that the air will only flow from the defroster vents, regardless of where it is commanded to. This Sierra has auto a/c controls and no floor mounted center console.
Of course the customer brought the truck in, knowing that I had to lay under the driver’s side of the dash and did not think to vacuum the floor board.
I checked the codes and sure enough there was a code B0263 stored in the HVAC module. Your scan tool has to be able to go into the body systems to see this information. A plain OBD2 scanner just won’t do the job. This repair is so common that you can diagnose it by symptom if you have to. The most common symptom of course is lack of control over the vent output position and normally it will be stuck in the defroster only position. If it is not currently stuck in the defroster position but you are changing the actuator anyways. make sure that you set the vent position to defrost before starting this procedure. You will see why later.
The data lines show an actual mode door position and a commanded mode door position. They do not even come close to matching.
I laid a fender cover on the dirty floor and set the parking brake pedal. The pedal hits me in the shoulder and prevents me from being able to maneuver around.
Now I am ready to get in there and work.
I start by removing the push pin that holds the driver’s floor vent extension in place.
With the push pin released the duct extensions pulls easily from the stationary duct.
The lower screw for the actuator is just above the duct work and cannot be seen. It has to be felt. 5.5 mm head
The second screw can be easily seen as it is at the upper edge of the actuator. Note that it also holds the wiring harness in place.
I have developed a slightly different twist to this repair procedure. I could not take good enough pictures from under the dash so hopefully I can show you how on the bench and you can transfer that knowledge to the vehicle.
With the two mounting screws removed and the wiring disconnected, use your fingers and thumb as leverage to push the cam/cog from the actuator shaft. The goal is to leave the cam/cog in place on the end of the heater-a/c case and to remove the actuator motor only.
The old assembly on the left and the new one on the right.
The old assembly separated
Taking the new actuator motor and installing it on the old cam/cog. Remember these steps will be done under the dash. Except for removing the new actuator motor from the new cam/cog, that can be done anywhere. I am just doing this on a bench to give you a clearer idea of what has to be done.
The old cam/cog with the new actuator motor installed. Note the positions of the cam/cog in relation to the motor. Assuming that your actuator has failed in the most common position, blowing out of the defroster vents only, you should not have to do anything other than installing the actuator motor. No indexing of the door shafts to the cam/cog or recalibration of the actuator motors. This is a big time saver.
If you need to purchase one of these actuators please click here.
I recently had to go behind someone that could not properly install the actuator. The actuator and cog were removed from the truck. I installed the cog with the upper peg inserted into the outer slot. I then moved the cog around so that the center/rotating boss dropped into it’s mating position on the HVAC box. Installed the actuator onto the cog and bolted it down. Once connected and activated the actuator turned the cog counter clockwise and indexed the gear tooth lever perfectly. I was a little surprised by this so I tried it several times and every time it aligned properly. When looking at the white geared lever there is one long tooth and when rotated that long tooth should overhang the last black tooth on the cog. Do Not forget that the actuator needs to be recalibrated in order to work correctly.
i have an 04 gmc sierra 2500hd the two bolts on the actuator are actually 8mm and in order to remove the top bolt you have to make a tool to fit i grinded a allen key down that fit a 1/4 inch drive socket then grinded down the 8mm socket only way to get in there but still no luck the motor doesnt move so im gonna check voltage tommorow – thanks for the excellent knowledge otherwise been quite a help
The only reason to check the indexing is if the actuator has been replaced recently and has not worked properly since installed. The tool is a 5.5 mm socket and 1/4″ palm ratchet. A regular ratchet will do.
Hello, my 2005 sierra only blows air out of the dash, i recalibrated the controls per you instructions and it is still stuck, since it is not stuck in defrost mode do I need to index the door shafts to the cam? and where do you get the little tool to take out the screws?
Hi Robert H,
The only things I can think of are that either there is a faulty actuator that is preventing the recalibration to work or the controls are being touched before the key is cycled off and back on. In either case I think the system will need to be checked for codes if possible.
Yes, you could have damaged it but start by checking the fuses. The connector for the blower switch is bad about burning out and you may have also moved it enough to loose the circuit. Check for ignition power on the brown wires. These trucks also have ground problems related to a loose ground on the back of the passeneger side cylinder head.